Black Box IC109A-R2 Instrukcja Instalacji Strona 153
- Strona / 164
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
14763230-216-229-B1
4
© 2007 Schneider Electric. All Rights Reserved.
Maintenance
Troubleshooting Assistance
MAJOR Fault: Sepam™ is in Fail-Safe Position
b ON LED of UMI on in front
b LED of UMI on in front
or LED of DSM303 remote advanced UMI flashing
b green LED on rear panel on
b red LED on rear panel on
PE50359
Major faults are only cleared after the cause
of the fault is corrected and Sepam™ is
switched on again.
PE50139
No Connection made with SFT2841
Possible Cause Action / Remedy
Memory cartridge absent. Switch off Sepam™.
Install the memory cartridge and secure it
by tightening the two integrated screws.
Switch Sepam™ on again (see page 150).
Fault message on display:
major fault
Major internal fault. Change base unit.
Connection made with SFT2841
Possible Cause Action / Remedy
SFT2841 indicates major fault, but no missing
module: Base unit internal fault.
Change base unit.
Memory cartridge not compatible with version of
the base unit (see below).
Note the version using the SFT2841 software,
Diagnosis screen.
Contact the local support team.
The hardware configuration is incorrect or
incomplete.
Use the SFT2841 software, in connected
mode, to determine the cause.
The SFT2841 Diagnosis screen displays the
missing items in red (see table below).
Check on hardware configuration using SFT2841
Diagnosis screen Possible cause Action / remedy
CCA630, CCA634, CCA671 or
CCA640 connector in B1 or B2
position displayed in red.
Connector absent. Install a connector.
If the connector is present,
check that it is plugged in
correctly and held in place
by the two screws.
LPCT sensors not connected. Connect the LPCT sensors.
Connector in position E
displayed in red.
Connector E unplugged or no
jumper between terminals 19
and 20.
Plug in connector E.
Fit the jumper.
MES120 module in H1, H2 or
H3 position displayed in red.
MES120 module absent. Install MES120 module.
If the MES120 module is
present, check that it is
plugged in correctly and held
in place by the two screws.
If the fault is still present,
replace the module.
PE10156
Fault message displayed
if cartridge is not compatible
Rules on Compatibility Between the Cartridge and the Base
Unit
The major index of the base-unit version must be greater than or equal to the major
index of the cartridge-application version.
Example: The base unit with a version V1.05 (major index = 1) and an application
with a version V2.00 (major index = 2) are not compatible.
If this rule is not observed, a major fault occurs and Sepam™ displays the message
in the left column.
1
- Series 80 1
- Protective Relays 1
- Safety Instructions 0 3
- Safety Instructions 8
- Before You Begin 8
- Introduction 10
- Modular Architecture 10
- Selection Table 11
- Technical Characteristics 13
- Environmental Characteristics 14
- Precautions 15
- Equipment Identification 16
- Main Units 18
- Accessories 19
- Replacement Equipment 20
- Base Unit 21
- Dimensions 21
- Mounting 22
- Connection 23
- Installing Terminal Guard 24
- Typical for Series 80 24
- CAUTION DANGER 25
- Installation 26
- Sepam™ B83 Connection Diagram 27
- Sepam™ C86 Connection Diagram 28
- Input for Sepam™ B80 34
- Connected Voltage Inputs 35
- 1A/5A Current Transformers 36
- Test Accessories 40
- CSH120 & CSH200 42
- Zero Sequence CT 42
- CSH30 Interposing Ring CT 44
- ACE990 Zero Sequence 47
- CT Interface 47
- Voltage Transformers 48
- MES120, MES120G, MES120H 50
- 14 Input/6 Output Modules 50
- Remote Modules 53
- MET1482 54
- Temperature Sensor Module 54
- Analog Output Module 56
- Remote Advanced UMI Module 58
- Sync-Check Module 60
- Communication Accessory 64
- Selection Guide 64
- Connection of Communication 65
- ACE937 Fiber Optic Interface 68
- ACE969TP and ACE969FO 69
- Multi-Protocol Interfaces 69
- Description 71
- RS232/RS485 Converter 74
- ACE919CA and ACE919CC 76
- RS485/RS485 Converters 76
- Communications Wiring 78
- Cable Pinouts 81
- Network Limits 82
- User-Machine Interfaces (UMI) 84
- User-Machine Interfaces 85
- DAMAGE TO CARTRIDGE 86
- CAUTION 87
- Local Operation on the UMI 88
- Password 91
- Settings 93
- SFT2841 Setup and Operating 96
- Welcome Window 96
- Connection Window 97
- SFT2841 Set Up and Operating 100
- Software 100
- General Screen Organization 100
- Using the Software 101
- Creating User Messages 102
- Disturbance Recording 103
- Logic-Equation Editing 104
- Program 105
- Default Settings 107
- Configuring Sepam™ 109
- SFT2841 Software 113
- Mimic-Diagram Editor 113
- Presentation 113
- Contents 123
- Principles 124
- Commissioning 125
- Equipment 126
- General Examination and 127
- Preliminary Actions 127
- Checking Input Connections 129
- 3-Phase Generator 129
- Single-Phase Generator & 130
- Voltages Delivered by 3 VT 130
- Checking Phase Current 132
- Input Connections 132
- For Differential Applications 132
- LPCT Type Current Sensors 133
- Checking Residual Current/ 134
- Voltage Input Connections 134
- Checking Residual Current 135
- Van = Vr 135
- Checking Residual Voltage 136
- Broken Delta Arrangement 136
- With Voltage Delivered by 137
- 1 Neutral Point VT 137
- Checking Sepam™ B80 138
- Additional Voltage 138
- Additional Voltage 139
- Checking Sepam™ B83 140
- Additional Phase Voltage 140
- Additional Residual Voltage 142
- Checking Sepam™ C86 143
- Unbalance Current 143
- Checking Logic Input & 144
- Output Connections 144
- Checking Optional 145
- Module Connections 145
- Validating the Complete 146
- Protection Chain 146
- Test Sheet 147
- Sepam™ Series 80 147
- Troubleshooting Assistance 152
- 152
- Replacing the Base Unit 156
- Replacing the Battery 156
- 3-Wire Power System 158
- 4-Wire Power System 159
- 63230-216-229-B1 161
- Schneider Electric USA 164
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.113 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji