Black Box IC109A-R2 Instrukcja Instalacji Strona 112
- Strona / 164
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
106
2
© 2007 Schneider Electric. All Rights Reserved.63230-216-229-B1
Use
SFT2841 Setting and Operating
Software
Configuring Sepam™
PE50591
Identifying Sepam™ Units Connected to the Communication
Network
The Sepam™ units connected to the communication network are identified by their
Modbus address.
You can configure these addresses in either of the following ways:
b Manually, one by one:
v use the Add button to define a new Sepam™ device; it is allocated a
default Modbus address
v use the Edit button to modify the Modbus address if necessary
v use the Delete button to remove a device from the configuration
b Automatically, by running an automatic search of the Sepam™ units
connected:
v the Automatic search / Stop search button starts or interrupts the search
v when SFT2841 recognizes a Sepam™ unit, its Modbus address and type
are shown on screen
v when a Modbus device other than Sepam™ responds to SFT2841, its
Modbus address is displayed. The text ??? indicates the device is not a
Sepam™
Press the OK button to close the UMI window and save the Sepam™ network
configuration settings.
Sepam™ network connected to SFT2841
PE50592
Access to Sepam™ Information
To establish communication between SFT2841 and a Sepam™ network, select the
Sepam™ network configuration you want, and press Connect.
The connection window displays the Sepam™ network. SFT2841 polls all the
equipment defined in the selected configuration. An icon represents each queried
Sepam™:
Sepam™ Series 20 or Series 40 connected to the network
Sepam™ Series 80 connected to the network
Sepam™ configured but not connected to the network
device other than Sepam™ connected to the network
A summary report of each detected Sepam™ is also displayed:
b Sepam™ Modbus address
b Type of application and Sepam™ identification
b Any alarms present
b Any minor/major faults present
Click the appropriate icon to access parameters, settings and operation, and
maintenance information for a particular Sepam™. SFT2841 will establish a point-to-
point connection with the selected Sepam™.
Access to parameters and settings for a Sepam™ Series 80
connected to a communication network
- Series 80 1
- Protective Relays 1
- Safety Instructions 0 3
- Safety Instructions 8
- Before You Begin 8
- Introduction 10
- Modular Architecture 10
- Selection Table 11
- Technical Characteristics 13
- Environmental Characteristics 14
- Precautions 15
- Equipment Identification 16
- Main Units 18
- Accessories 19
- Replacement Equipment 20
- Base Unit 21
- Dimensions 21
- Mounting 22
- Connection 23
- Installing Terminal Guard 24
- Typical for Series 80 24
- CAUTION DANGER 25
- Installation 26
- Sepam™ B83 Connection Diagram 27
- Sepam™ C86 Connection Diagram 28
- Input for Sepam™ B80 34
- Connected Voltage Inputs 35
- 1A/5A Current Transformers 36
- Test Accessories 40
- CSH120 & CSH200 42
- Zero Sequence CT 42
- CSH30 Interposing Ring CT 44
- ACE990 Zero Sequence 47
- CT Interface 47
- Voltage Transformers 48
- MES120, MES120G, MES120H 50
- 14 Input/6 Output Modules 50
- Remote Modules 53
- MET1482 54
- Temperature Sensor Module 54
- Analog Output Module 56
- Remote Advanced UMI Module 58
- Sync-Check Module 60
- Communication Accessory 64
- Selection Guide 64
- Connection of Communication 65
- ACE937 Fiber Optic Interface 68
- ACE969TP and ACE969FO 69
- Multi-Protocol Interfaces 69
- Description 71
- RS232/RS485 Converter 74
- ACE919CA and ACE919CC 76
- RS485/RS485 Converters 76
- Communications Wiring 78
- Cable Pinouts 81
- Network Limits 82
- User-Machine Interfaces (UMI) 84
- User-Machine Interfaces 85
- DAMAGE TO CARTRIDGE 86
- CAUTION 87
- Local Operation on the UMI 88
- Password 91
- Settings 93
- SFT2841 Setup and Operating 96
- Welcome Window 96
- Connection Window 97
- SFT2841 Set Up and Operating 100
- Software 100
- General Screen Organization 100
- Using the Software 101
- Creating User Messages 102
- Disturbance Recording 103
- Logic-Equation Editing 104
- Program 105
- Default Settings 107
- Configuring Sepam™ 109
- SFT2841 Software 113
- Mimic-Diagram Editor 113
- Presentation 113
- Contents 123
- Principles 124
- Commissioning 125
- Equipment 126
- General Examination and 127
- Preliminary Actions 127
- Checking Input Connections 129
- 3-Phase Generator 129
- Single-Phase Generator & 130
- Voltages Delivered by 3 VT 130
- Checking Phase Current 132
- Input Connections 132
- For Differential Applications 132
- LPCT Type Current Sensors 133
- Checking Residual Current/ 134
- Voltage Input Connections 134
- Checking Residual Current 135
- Van = Vr 135
- Checking Residual Voltage 136
- Broken Delta Arrangement 136
- With Voltage Delivered by 137
- 1 Neutral Point VT 137
- Checking Sepam™ B80 138
- Additional Voltage 138
- Additional Voltage 139
- Checking Sepam™ B83 140
- Additional Phase Voltage 140
- Additional Residual Voltage 142
- Checking Sepam™ C86 143
- Unbalance Current 143
- Checking Logic Input & 144
- Output Connections 144
- Checking Optional 145
- Module Connections 145
- Validating the Complete 146
- Protection Chain 146
- Test Sheet 147
- Sepam™ Series 80 147
- Troubleshooting Assistance 152
- 152
- Replacing the Base Unit 156
- Replacing the Battery 156
- 3-Wire Power System 158
- 4-Wire Power System 159
- 63230-216-229-B1 161
- Schneider Electric USA 164
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji