Black Box Wizard IP Plus ServSwitchTM Podręcznik Użytkownika Strona 27
- Strona / 79
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
26
®
Wizard IP Plus Maintenance
Reset Configuration
return to normal operation.
Configure Network
Put option switch 1 up to
To upgrade unit, visit:
http://192.168.42.154
Wizard IP Plus Network Config
Net Mask 255.255.255.0
192.168.42.154
No
Gateway
OK
IP Address
00:0F:58:00:00:04
Use DHCP
MAC Address
Performing a flash upgrade
Wizard IP Plus is fully reconfigurable via flash upgrade.
To perform a flash upgrade
1 Using a remote connection, log on as the admin user and access the Unit
configuration page to determine the current firmware version of the
Wizard IP Plus unit.
2 Visit the Black Box website, locate the downloads section and select an
Wizard IP Plus firmware revision that is later than the one currently installed.
3 Power down the Wizard IP Plus unit. At the rear of the unit, adjacent to the
power input socket, click mini switch 1 to its ON (down) position.
4 Re-apply power to the Wizard IP Plus. On the locally connected monitor you
should see a Maintenance menu:
The Maintenance menu should display the current network address
of the Wizard IP Plus.
• If the current network address is incorrect then select
the ‘Configure network’ option to change it:
5 Using the web browser (not the VNC viewer) on the previously used remote
system, connect to the network address shown in the local Maintenance
menu.
6 Follow the on screen instructions to upload the firmware file (previously
obtained from Black Box support) to the Wizard IP Plus.
IMPORTANT: Wait until the upgrade is complete.
7 When the upload is complete and confirmed on screen, log off the remote
system and then power down the Wizard IP Plus.
8 At the rear of the unit, return the mini switch 1 to its OFF position and then
re-apply power.
MAC address
Media Access Control address – this is
the unique and unchangeable code that
was hard coded within your Wizard IP
Plus unit when it was built. It consists
of six 2-digit hexadecimal (base 16)
numbers separated by colons. A section
of the MAC address identifies the
manufacturer, while the remainder is
effectively the unique electronic serial
number of your particular unit.
Use DHCP
When this option is selected, your Wizard
IP Plus will attempt to locate a DHCP
server on the network. If such a server is
located, it will supply three things to
the Wizard IP Plus: an IP address, an IP
network mask (also known as a Subnet
mask) and a Gateway address.
IP address
This is the identity of the Wizard IP
Plus within a network. It can either
be entered manually or configured
automatically using the DHCP option.
When the DHCP option is enabled, this
entry is greyed out.
Net mask
Also often called the ‘subnet-mask’, this
value is used alongside the IP address
to help define a smaller collection (or
subnet) of devices on a network. In
this way a distinction is made between
locally connected devices and ones that
are reachable elsewhere, such as on the
wider Internet.
Gateway
This is the address of the device that links
the local network (to which the Wizard
IP Plus is connected) to another network
such as the Internet. Usually this is a
network switch or router and it will be
used whenever a device to be contacted
lies outside the local network.
Configure network option
Current network
address of the
Wizard IP Plus
Note: It is also possible to upgrade the
Wizard IP Plus from a remote position via
the Advanced Unit Configuration page
of the VNC Viewer.
- ServSwitch 1
- Wizard IP Plus 1
- Contents 2
- Further information 3
- Introduction 4
- BLACK BOX 5
- What’s in the box 6
- Installation 7
- Connections 8
- Host computer links: Video 9
- Host computer links: Audio 10
- 11
- 11
- 11
- IP network port 13
- Modem/ISDN port 14
- Power supply connection 14
- Power control port 15
- > > > 16
- Encryption settings 18
- Resetting the configuration 20
- Part 2 – Remote configuration 21
- Networking issues 22
- Power switching configuration 25
- Pxy=z\0D 25
- The KVMADMIN utility 26
- Performing a flash upgrade 27
- Operation 28
- Remote connections 29
- Local connection (continued) 29
- The menu bar 31
- When using the viewer window 31
- Host selection 32
- Configure 32
- Mouse pointers 32
- Access mode - shared/private 33
- Power control 33
- Auto calibrate 33
- Re-synchronise mouse 33
- Controls 34
- Viewer encryption settings 39
- Supported web browsers 39
- Unit configuration 42
- Network configuration 43
- Modem configuration 44
- Reset configuration 45
- Clear IP access control 46
- Colour/Encoding 47
- Identities 50
- Load / Save 50
- Encoding and colour level 52
- Security 52
- User accounts 54
- Advanced unit configuration 56
- Time & date configuration 57
- Setting IP access control 59
- Modem port 60
- Host configuration 61
- Hotkey sequences 62
- Port Direct 62
- Logging and status 63
- 192.168.142.154 64
- Security issues with ports 67
- Permissible key presses 69
- Creating macro sequences 69
- Safety information 71
- End user licence agreement 72
- Radio Frequency Energy 73
- Instrucciones de seguridad 75
Powiązane produkty i podręczniki dla Przełączniki KVM Black Box Wizard IP Plus ServSwitchTM
Przełączniki KVM Black Box ACS201A Dokumentacja
(41 strony)
(41 strony)
Przełączniki KVM Black Box 16 port Dokumentacja
(33 strony)
(33 strony)
Przełączniki KVM Black Box KV0004A Dokumentacja
(43 strony)
(43 strony)
Przełączniki KVM Black Box SW619A Dokumentacja
(57 strony)
(57 strony)
Przełączniki KVM Black Box KV1161A Dokumentacja
(22 strony)
(22 strony)
Przełączniki KVM Black Box ACU3009A Dokumentacja
(49 strony)
(49 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji