Black Box TV Converter Box 10/100 Autosensing Media Converter Instrukcja Użytkownika Pobierz pdf

10/100 Autosensing

Media Converter

Installation Guide

LMC7001A-R4 – LMC7002A-R4 – LMC7003A-R4 – LMC7004A-R4 – LMC7005A – LMC7006A

10/100 Autosensing Media Converter™ is a low-cost, standalone, IEEE

802.3 single-conversion media converter which converts between:

10Base-T twisted pair and 10Base-FL single or multi-mode fiber;

100Base-TX twisted pair and 100Base-SX multi-mode fiber

100Base-TX twisted pair and 100Base-FX single-mode fiber

10/100 Autosensing Media Converter is a 1U high, table-top unit that

includes diagnostic LEDs, an internal, universal (100/240 VAC) power

supply, one RJ-45 connector for the twisted pair port and one pair of ST

(LMC7001A-R4 for 850 nm multi-mode, LMC7005A for 1300 nm multi-

mode, and LMC7003A-R4 for 1310 nm single mode) or SC (LMC7002A-R4

for 850 nm multi-mode, LMC7006A for 1300 nm multi-mode, and

LMC7004A-R4 for 1310 nm single-mode) connectors for the fiber port.

Installing 10/100 Autosensing Media Converter

10/100 Autosensing Media Converter comes ready to install. The only

adjustments that may need to be made after installation are:

Configuring the unit for its mode of operation and other features.

Setting the twisted pair port for a crossover workstation or pass-

through connection.

To install the

10/100 Autosensing Media Converter, first make sure that the

unit is placed on a suitable flat surface, leaving some space behind the unit.

Attach the cables between the

10/100 Autosensing Media Converter and each

device that will be interconnected, then plug the unit into a reliable, filtered

power source.

NOTE: All network cables must be connected for link LEDs to glow.

The following diagram shows the faceplate on the 10/100 Autosensing

Media Converter

. Regardless of the type of fiber connectors, the LEDs

operate the same. Refer to page 5 for LED functionality.

XMT RCV

Crossover/

pass-through

switch

Fiber Optic

port

LEDs

10/100 Mbps

X II

100

PWR

100

ACT

LNK

ACT

LNK

Twisted Pair

LEDs

1000 Park Drive • Lawrence, PA 15055-1018 USA

TEL: (724) 746-5500 • FAX: 724-746-0746

[email protected] • www.blackbox.com

The information in this document is subject to change without notice. Black Box assumes no responsibility for any errors that may appear

in this document. All product names are trademarks of the manufacturer. Specific brands and product names may be trademarks and are

the property of their respective companies.

Document Number 55-80216BB-01 B6 January 2005

1 2 3 4

Podsumowanie treści

Strona 1 - Media Converter

8110/100 Autosensing Media ConverterInstallation GuideLMC7001A-R4 – LMC7002A-R4 – LMC7003A-R4 – LMC7004A-R4 – LMC7005A – LMC7006A10/100 Autosensing Me

Strona 2 - ODE SWITCH FUNCTION DEFAULT

27Configuration Instructions10/100 Autosensing Media Converters featuresan 8-position DIP switch for configuring the unit.This switch is accessed thro

Strona 3 - Black Box Customer Service

•In Force 100 mode, the media converter converts 100Base-TX to100Base-SX multi-mode or 100Base-FX single-mode fiber; 10 Mbpssignals are not accepted.

Strona 4 - Installation Troubleshooting

45L INK F AULT D ETECTION F EATURELink Fault Detection is only available when using Force-10 or Force-100mode; it is not available in Auto-Negotiatio

Komentarze do niniejszej Instrukcji

Brak uwag

Black Box TV Converter Box 10/100 Autosensing Media Converter Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Konwertery mediów sieciowych Black Box TV Converter Box 10/100 Autosensing Media Converter. Black Box TV Converter Box 10/100 Autosensing Media Converter User's Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Konwertery mediów sieciowych Black Box TV Converter Box 10/100 Autosensing Media Converter